Thermal Compliance
TRAINING, CONSULTANCY
​VALIDATION AND CALIBRATION SERVICES
​
UK +44 (0)1748 327 247
  • Home
  • Training
  • Consultancy
  • Validation Services
    • Remote Validation
    • Autoclave Validation >
      • Using Wireless Dataloggers for Autoclave Validation
    • Temperature Mapping >
      • LN2 and ULT Freezers
      • Warehouse Mapping
      • Humidity & CO2 Testing
      • Dataloggers
      • What is Temperature Mapping?
      • Wireless Dataloggers for Thermal Validation
  • Equipment Rental
    • Kaye Equipment Rental
  • Clients
  • Contact us
    • About TCL
    • Downloads
  • News

EN285 - Standard Towel Packs

30/1/2019

0 Comments

 
The Standard Test pack is used to test the performance of an autoclave and ensure rapid and even penetration of steam within the pack. The test originates from UK Health Technical Memorandums (HTMs)and is well known from HTM2010.

Standard Test Packs are a great way of testing and setting up autoclave cycles. There use is detailed in EN285:2015 for the following tests:
​
​·       Small/Full Load Thermometric Tests 
·       Air Detector Performance Tests
·       Load Dryness Test
·       Air Detector Function Test
We often hear of failures during benchmark testing to EN285 and these can often stem from the preparation for the standard test pack. Below are a few simple ways to ensure your pack is suitable for use:

1.       The pack should be laundered when soiled, this must be done without the use of detergent or conditioner            (which may cause Non Condensable Gases)
2.       The pack must be allowed to equilibrate between 20-30°C and a humidity of 40 to 60% RH.
3.       The pack should weigh 7.0kg +/-0.14kg
4.       The Pack should be folded as shown in Figure 13 of EN 285:2015.

 
The specification or the test pack is detailed in EN285:2015 section 23.1. If you would like to purchase suitable Standard Test Packs or if you have experienced failures and would like advice, please let us know and we would be happy to help.

We can also help with hire of
  • Sword Hygrometer for checking Temperature and Humidity Conditioning of the Pack
  • KERN Balance suitable for weighing the Standard Test Pack.
  • Pre Conditioned Test Packs
  • Steam Quality Test Kits

If you would like to know more about our EN285 Test Equipment Hire please take a look at our Validation Accesories hire page.
0 Comments

CO2 Incubator Mapping

30/1/2019

0 Comments

 
Picture
At Thermal Compliance we use several systems for temperature mapping and validation. We do this to ensure the system we use is best suited to your application. 

For CO2 Incubators we use Ellab Tracksense CO2 sensors to map CO2. This sensor provides 21 CFR Part 11 compliant data and allows us to map CO2 for the duration of the validation. This allows our engineers to ensure your CO2 Incubator is optimised for your process.

​Alongside our CO2 sensors we also use Ellab Tracksense Pro and Tracksense Lab sensors to map Temperature and Humidity. With a clear and concise Pass/Fail report detailing acceptance criteria for temperature, humidity and CO2.

If you would like to know more about how we can help and about our different CO2 Systems, please visit http://www.thermalcompliance.co.uk/humidity--co2-testing.html 
0 Comments

    RSS Feed

    Tweets by @ThermalCom

    Archives

    August 2022
    April 2022
    December 2021
    October 2021
    July 2021
    June 2021
    May 2021
    January 2021
    December 2020
    November 2020
    August 2020
    July 2020
    June 2020
    March 2020
    February 2020
    November 2019
    October 2019
    September 2019
    August 2019
    July 2019
    June 2019
    May 2019
    April 2019
    March 2019
    February 2019
    January 2019
    December 2018
    November 2018
    October 2018
    August 2018
    July 2018
    March 2018
    January 2018
    November 2017
    October 2017
    August 2017
    June 2017
    April 2017
    March 2017
    February 2017
    December 2016
    October 2016
    June 2016
    March 2016
    December 2015
    October 2015
    August 2015
    April 2015
    February 2015
    January 2015
    October 2014
    July 2014
    June 2014
    May 2014
    April 2014
    February 2014
    January 2014
    December 2013
    November 2013
    October 2013
    September 2013
    August 2013
    July 2013
    June 2013

    Brochure
    File Size: 1573 kb
    File Type: pdf
    Download File

Picture
COMPANY
Home Page
News & Updates
Contact Us
About Us

Privacy Policy & Terms
OUR SERVICES
Validation
    Autoclave Validation
    Steam In Place Validation
​    Temperature Mapping
Remote Validation
​Training
Consultancy
​   What is temperature Mapping?
Equipment Rental
Thermal Compliance Ltd. Registered in England. Number 6155116. © Copyright Thermal Compliance Limited 2007-2019.
Registered Address: 18 Harelands Courtyard Offices, Moor Road, Richmond, North Yorkshire. DL10 5NY.  VAT Number GB915 787780000